How To Reset Horizon Treadmill Lube Belt

So, picture this: You're midway through your daily 5k on your trusty Horizon treadmill, when suddenly, it starts sounding like a stampede of elephants. The belt's decided it's time for a change, and it's not being subtle about it. That's when you realize, it's time to give your treadmill some TLC and reset that lube belt.

Why Reset the Lube Belt?

First things first, why bother resetting the lube belt? Well, friend, it's all about longevity and smooth operation. The lube belt, or the 'lubrication' belt, keeps your treadmill's belt running smoothly. Over time, it can get clogged with dust and debris, leading to that not-so-silent protest we experienced earlier. Resetting it ensures your treadmill's belt stays well-lubricated and quiet.

Before You Start

Before we dive in, let's make sure you've got the right tools for the job. You'll need a Phillips screwdriver, a flathead screwdriver, and some WD-40 or silicone spray. Oh, and a towel or some rags to clean up the mess. Trust me, you'll thank me later for that one.

Step 1: Access the Lubrication System

Alright, let's get started. First, you'll need to access the lubrication system. To do this, you'll need to remove the motor cover. It's usually held in place by a few screws. Once you've removed them, gently lift the cover off. Be careful, there might be some lubricant inside, so have your towel ready.

Step 2: Remove the Lubrication Belt

Now that you've got the cover off, you should see the lubrication belt. It's the one that runs over the lubrication pump. To remove it, you'll need to loosen the tension on the belt. There's usually a screw or a lever that does this. Once you've loosened it, you can slide the belt off the pump.

Step 3: Clean the Lubrication Pump

This is where it gets a bit messy. The lubrication pump can get clogged with dust and debris. To clean it, you'll need to remove the pump from the treadmill. It's usually held in place by a few screws. Once you've removed it, use a flathead screwdriver to clean out the pump. Be gentle, we don't want to damage it.

Lube Horizon Treadmill at Pearline Beard blog

Step 4: Lubricate the Belt

Now that the pump's clean, it's time to lubricate the belt. Spray some WD-40 or silicone spray onto a rag, then wipe the belt with it. Make sure to get both sides of the belt. You don't need to drown it in lubricant, a little goes a long way.

Step 5: Reset the Lubrication Belt

Alright, the fun part. Well, the easiest part, at least. To reset the lubrication belt, you'll need to turn the treadmill's belt over. This is usually done by turning a screw on the side of the treadmill. Once you've turned it over, the lubrication belt should be on the right side of the belt. If it's not, you might need to adjust the belt's position.

Step 6: Test the Treadmill

Now that you've reset the lube belt, it's time to test the treadmill. Turn it on and let it run for a few minutes. If it's quiet and smooth, you've done it right! If not, don't worry, we'll troubleshoot in a bit.

Horizon T101 Treadmill Lube Belt at Caitlyn Lavater blog

Troubleshooting

Alright, so your treadmill's still sounding like a herd of elephants. Don't panic, we can fix this. First, let's check if the lubrication belt is running over the lubrication pump. If it's not, you might need to adjust the belt's position.

If the belt's running over the pump but it's still not quiet, it might be time to replace the lubrication belt. They don't last forever, you know. If you're not comfortable doing this yourself, don't hesitate to call a professional.

And there you have it, folks! Your treadmill should now be running smoothly and quietly. Remember, regular maintenance is key to keeping your treadmill in tip-top shape. So, don't forget to reset that lube belt every now and then. Your ears will thank you!